Difference between revisions of "Installing and using software with Gigabot"
(→USB to serial driver) |
(→Install software) |
||
Line 18: | Line 18: | ||
===Slic3r=== | ===Slic3r=== | ||
Slic3r takes a 3D model (usually an .stl file) and turns it into G-code. G-code is the instructions for the 3D printer to create the part. A more detailed understanding of G-code can be found on the [http://reprap.org/wiki/Gcode RepRap wiki]. | Slic3r takes a 3D model (usually an .stl file) and turns it into G-code. G-code is the instructions for the 3D printer to create the part. A more detailed understanding of G-code can be found on the [http://reprap.org/wiki/Gcode RepRap wiki]. | ||
+ | |||
:Download and install [http://slic3r.org/ Slic3r]. | :Download and install [http://slic3r.org/ Slic3r]. | ||
+ | |||
:Read the complete [http://manual.slic3r.org/ Slic3r manual] | :Read the complete [http://manual.slic3r.org/ Slic3r manual] | ||
+ | |||
:Download Slic3r settings [[File:Gigabot_Slic3r_config.ini]] to your local computer. | :Download Slic3r settings [[File:Gigabot_Slic3r_config.ini]] to your local computer. | ||
+ | |||
:Open Slic3r and go to File -> Preferences -> Mode -> Expert | :Open Slic3r and go to File -> Preferences -> Mode -> Expert | ||
+ | |||
:Click OK and follow prompt to restart Slic3r | :Click OK and follow prompt to restart Slic3r | ||
+ | |||
:Once you have restarted Slic3r go to File -> Load Configuration | :Once you have restarted Slic3r go to File -> Load Configuration | ||
+ | |||
:Choose the Gigabot_Slic3r_config.ini configuration file you saved earlier | :Choose the Gigabot_Slic3r_config.ini configuration file you saved earlier | ||
Line 39: | Line 46: | ||
:Download and install [http://koti.kapsi.fi/~kliment/printrun/ Printrun for Windows or Mac]. | :Download and install [http://koti.kapsi.fi/~kliment/printrun/ Printrun for Windows or Mac]. | ||
+ | |||
:Open Pronterface and go to Settings -> Options | :Open Pronterface and go to Settings -> Options | ||
+ | |||
:Under the Printer Settings tab change: | :Under the Printer Settings tab change: | ||
+ | |||
:Baud rate to 250000 | :Baud rate to 250000 | ||
+ | |||
:Bed temp for PLA to 65 | :Bed temp for PLA to 65 | ||
+ | |||
:Extruder temp for PLA to 195 | :Extruder temp for PLA to 195 | ||
+ | |||
:X and Y manual feed rate to 6000 | :X and Y manual feed rate to 6000 | ||
+ | |||
:Z manual feed rate to 200 | :Z manual feed rate to 200 | ||
+ | |||
:E manual feed rate to 100 | :E manual feed rate to 100 | ||
+ | |||
:Width, Depth and Height to 600 | :Width, Depth and Height to 600 | ||
+ | |||
:Click OK then restart Pronterface for the changes to take affect | :Click OK then restart Pronterface for the changes to take affect | ||
+ | |||
:With Gigabot turned on, plug the USB cable into your computer | :With Gigabot turned on, plug the USB cable into your computer | ||
+ | |||
:In Pronterface click on the 'Connect' button at the top left of the main screen | :In Pronterface click on the 'Connect' button at the top left of the main screen | ||
+ | |||
:Once connected the dialog box on the right side of the screen should say 'Printer now online' | :Once connected the dialog box on the right side of the screen should say 'Printer now online' | ||
+ | |||
:On the left side of the screen near the Check Temperature button activate the "Watch" check box | :On the left side of the screen near the Check Temperature button activate the "Watch" check box | ||
+ | |||
:In the Pronterface control panel click on the +x 10 button to move the print head to the right 10mm | :In the Pronterface control panel click on the +x 10 button to move the print head to the right 10mm | ||
+ | |||
:Note: Calibrate the bed using the below instructions before moving the Z axis | :Note: Calibrate the bed using the below instructions before moving the Z axis |
Revision as of 16:50, 3 August 2014
Contents
Install software
Gigabot is fully compatible with open source programming tools supported by the RepRap community. We encourage you to become an active participant in this thriving community!
- There are two software programs and one USB to serial driver required for printing with Gigabot. The first software one will translate the solid model into G-code and the second one can be used to feed the G-code to Gigabot.
USB to serial driver
The Virtual Communications Port driver talks to your USB port in a way that Gigabot understands.
- Download and install the VCP driver for your specific operating system.
- You may need administrator rights, or need to right click and "Run as Administrator".
Slic3r
Slic3r takes a 3D model (usually an .stl file) and turns it into G-code. G-code is the instructions for the 3D printer to create the part. A more detailed understanding of G-code can be found on the RepRap wiki.
- Download and install Slic3r.
- Read the complete Slic3r manual
- Download Slic3r settings File:Gigabot Slic3r config.ini to your local computer.
- Open Slic3r and go to File -> Preferences -> Mode -> Expert
- Click OK and follow prompt to restart Slic3r
- Once you have restarted Slic3r go to File -> Load Configuration
- Choose the Gigabot_Slic3r_config.ini configuration file you saved earlier
Simplify3D
- A great place to start is the simplify 3d website: http://www.simplify3d.com/support/
- Helpful tutorials: http://www.simplify3d.com/support/tutorials/
- Here is the configuration file for using Simplify with Gigabot: File:Gigabot Simplify3D config.fff
Printrun (Pronterface)
This program is the interface you will use to communicate with Gigabot. Once the 3D model (.stl) has been turned into G-code, it must be feed into the printer. This can be done by loading the G-code file onto a micro SD card and inserting it into Gigabot's Viki controller or feeding it from your computer to Gigabot via Pronterface. More information on Pronterface can be found Here
- Download and install Printrun for Windows or Mac.
- Open Pronterface and go to Settings -> Options
- Under the Printer Settings tab change:
- Baud rate to 250000
- Bed temp for PLA to 65
- Extruder temp for PLA to 195
- X and Y manual feed rate to 6000
- Z manual feed rate to 200
- E manual feed rate to 100
- Width, Depth and Height to 600
- Click OK then restart Pronterface for the changes to take affect
- With Gigabot turned on, plug the USB cable into your computer
- In Pronterface click on the 'Connect' button at the top left of the main screen
- Once connected the dialog box on the right side of the screen should say 'Printer now online'
- On the left side of the screen near the Check Temperature button activate the "Watch" check box
- In the Pronterface control panel click on the +x 10 button to move the print head to the right 10mm
- Note: Calibrate the bed using the below instructions before moving the Z axis