Difference between revisions of "Tuning hot-end temperature controller"
From re:3D
Line 1: | Line 1: | ||
− | + | ===Single Extruder=== | |
+ | #Connect Gigabot's power and USB cables. | ||
+ | #Use Pronterface connect to Gigabot. | ||
+ | #Turn on the head fan by typing M106 S255 command in the lower right corner of Pronterface. | ||
+ | #If you have previously been printing wait for the hot-end to cool below 100C. | ||
+ | #In Pronterface type into the data entry box at the lower right corner: | ||
+ | |||
+ | ::For GB2 use “M303 S200” | ||
+ | ::For GB3 Left Extruder use “M303 E0 S200” | ||
+ | |||
+ | This will start the PID auto-tune function in the Marlin Firmware. The hot-end will cycle the heat up and down for a couple minutes until displaying the message: "PID Autotune Complete". | ||
+ | #Write down the last set of output values given. | ||
+ | |||
+ | :Classic PID | ||
+ | :Kp: 50.03 | ||
+ | :Ki: 1.98 | ||
+ | :Kd: 150.98 | ||
+ | |||
+ | Adjusting the firmware | ||
+ | #In Pronterface DISCONNECT from Gigabot, Close Pronterface, RESTART Pronterface. | ||
+ | #Connect to Gigabot. | ||
+ | #In Pronterface type into the data entry box at the lower right corner: "M301 H1 P(your Kp value) I(your Ki value) D(your Kd value)". | ||
+ | #It should look like this using the example above: | ||
+ | |||
+ | "M301 H1 P50.03 I1.98 D150.98" This will temporarily change the current settings for the temperature controller | ||
+ | |||
+ | #It should look like this using the example above: "M301 H1 P50.03 I1.98 D150.98" This will TEMPORARILY change the current settings for the temperature controller. | ||
+ | #In Pronterface type into the data entry box at the lower right corner: "M500" This will make changes permanent. | ||
+ | #In Pronterface: Set hot-end temperature to 200C and watch that it comes up to temp, overshoot the target temp slightly, undershoot temp slightly and then settles onto the target temp within 1-2 deg. | ||
+ | ===Dual Extruder=== | ||
#Connect Gigabot's power and USB cables. | #Connect Gigabot's power and USB cables. | ||
#In Pronterface connect to Gigabot. | #In Pronterface connect to Gigabot. | ||
Line 6: | Line 35: | ||
#If you have previously been printing wait for the hot-end to cool. | #If you have previously been printing wait for the hot-end to cool. | ||
#In Pronterface type into the data entry box at the lower right corner: | #In Pronterface type into the data entry box at the lower right corner: | ||
− | + | ||
::For GB3 Left Extruder use “M303 E0 S200” | ::For GB3 Left Extruder use “M303 E0 S200” | ||
− | ::For GB3 | + | ::For GB3 Right Extruder use “M303 E1 S200” |
This will start the PID auto-tune function in the Marlin Firmware. The hot-end will cycle the heat up and down for a couple minutes until displaying the message: "PID Autotune Complete". | This will start the PID auto-tune function in the Marlin Firmware. The hot-end will cycle the heat up and down for a couple minutes until displaying the message: "PID Autotune Complete". | ||
Line 21: | Line 50: | ||
#In Pronterface disconnect from Gigabot, Close Pronterface, Restart Pronterface. | #In Pronterface disconnect from Gigabot, Close Pronterface, Restart Pronterface. | ||
#Connect to Gigabot. | #Connect to Gigabot. | ||
− | #In Pronterface type into the data entry box at the lower right corner: "M301 H1 P(your Kp value) I(your Ki value) D(your Kd value)" | + | #In Pronterface type into the data entry box at the lower right corner: |
− | #It should look like this using the example above: "M301 H1 P50.03 I1.98 D150.98" This will | + | |
− | #In Pronterface type into the data entry box at the lower right corner: "M500" This will | + | Left Extruder "M301 H1 P(your Kp value) I(your Ki value) D(your Kd value)" |
+ | Right Extruder "M301 H2 P(your Kp value) I(your Ki value) D(your Kd value)" | ||
+ | |||
+ | #It should look like this using the example above: "M301 H1 P50.03 I1.98 D150.98" This will TEMPORARILY change the current settings for the temperature controller. | ||
+ | #In Pronterface type into the data entry box at the lower right corner: "M500" This will make changes permanent. | ||
#In Pronterface: Set hot-end temperature to 200C and watch that it comes up to temp, overshoot the target temp slightly, undershoot temp slightly and then settles onto the target temp within 1-2 deg. | #In Pronterface: Set hot-end temperature to 200C and watch that it comes up to temp, overshoot the target temp slightly, undershoot temp slightly and then settles onto the target temp within 1-2 deg. |
Revision as of 19:56, 26 March 2016
Single Extruder
- Connect Gigabot's power and USB cables.
- Use Pronterface connect to Gigabot.
- Turn on the head fan by typing M106 S255 command in the lower right corner of Pronterface.
- If you have previously been printing wait for the hot-end to cool below 100C.
- In Pronterface type into the data entry box at the lower right corner:
- For GB2 use “M303 S200”
- For GB3 Left Extruder use “M303 E0 S200”
This will start the PID auto-tune function in the Marlin Firmware. The hot-end will cycle the heat up and down for a couple minutes until displaying the message: "PID Autotune Complete".
- Write down the last set of output values given.
- Classic PID
- Kp: 50.03
- Ki: 1.98
- Kd: 150.98
Adjusting the firmware
- In Pronterface DISCONNECT from Gigabot, Close Pronterface, RESTART Pronterface.
- Connect to Gigabot.
- In Pronterface type into the data entry box at the lower right corner: "M301 H1 P(your Kp value) I(your Ki value) D(your Kd value)".
- It should look like this using the example above:
"M301 H1 P50.03 I1.98 D150.98" This will temporarily change the current settings for the temperature controller
- It should look like this using the example above: "M301 H1 P50.03 I1.98 D150.98" This will TEMPORARILY change the current settings for the temperature controller.
- In Pronterface type into the data entry box at the lower right corner: "M500" This will make changes permanent.
- In Pronterface: Set hot-end temperature to 200C and watch that it comes up to temp, overshoot the target temp slightly, undershoot temp slightly and then settles onto the target temp within 1-2 deg.
Dual Extruder
- Connect Gigabot's power and USB cables.
- In Pronterface connect to Gigabot.
- Turn on the head fan by typing M106 S255 command in the lower right corner of Pronterface.
- If you have previously been printing wait for the hot-end to cool.
- In Pronterface type into the data entry box at the lower right corner:
- For GB3 Left Extruder use “M303 E0 S200”
- For GB3 Right Extruder use “M303 E1 S200”
This will start the PID auto-tune function in the Marlin Firmware. The hot-end will cycle the heat up and down for a couple minutes until displaying the message: "PID Autotune Complete".
- Write down the last set of output values given.
- Classic PID
- Kp: 50.03
- Ki: 1.98
- Kd: 150.98
Adjusting the firmware
- In Pronterface disconnect from Gigabot, Close Pronterface, Restart Pronterface.
- Connect to Gigabot.
- In Pronterface type into the data entry box at the lower right corner:
Left Extruder "M301 H1 P(your Kp value) I(your Ki value) D(your Kd value)" Right Extruder "M301 H2 P(your Kp value) I(your Ki value) D(your Kd value)"
- It should look like this using the example above: "M301 H1 P50.03 I1.98 D150.98" This will TEMPORARILY change the current settings for the temperature controller.
- In Pronterface type into the data entry box at the lower right corner: "M500" This will make changes permanent.
- In Pronterface: Set hot-end temperature to 200C and watch that it comes up to temp, overshoot the target temp slightly, undershoot temp slightly and then settles onto the target temp within 1-2 deg.