Strain Relief Cable Gland - Revision history

Matthew at 21:44, 9 January 2015

2015-01-09T21:44:55Z

2015-01-09T21:43:28Z

2015-01-09T21:33:32Z

2015-01-09T21:19:34Z

2015-01-09T20:31:38Z

2014-12-26T15:19:09Z

New page

[[File:Strain_Relief_Cable_Glad.jpg]]

← Older revision		Revision as of 21:44, 9 January 2015
Line 40:		Line 40:
	*Note when wrapping spiral wrap start at the print head and wrap towards the electrical box.		*Note when wrapping spiral wrap start at the print head and wrap towards the electrical box.

−	Ensure the extruder motor wire and the head cable have good amount of free wire and ~~stressing~~ the connections.	+	Ensure the extruder motor wire and the head cable have good amount of free wire and not pulling on the connections.

@@ Line 26: / Line 26: @@
 [[File:5.jpg]]
+Open electrical box door and loosen head cable wires from the Azteeg
 [[File:6.jpg]]
-Open electrical box door and loosen head cable wires from the Azteeg
+*red and black cartridge heater wires from the left side

@@ Line 11: / Line 11: @@
 Loosen six terminal screws where the head cable wires attach. *may need to loosen the upper six terminal screws as wire may be held by upper screws as well
@@ Line 21: / Line 19: @@
 Unwrap spiral wrap.
-[[File:5.jpg]]
+[[File:4.jpg]]
 Remove cable grommet and head cable from in the head junction box.
 * The flex cable gland is shown; some Gigabots may have a regular cable grommet in it’s place.
 [[File:6.jpg]]
 Open electrical box door and loosen head cable wires from the Azteeg

@@ Line 2: / Line 2: @@
 For safety we're going to turn off the Gigabot and unplug the machine from the wall.
 [[File:1.jpg]]
-Move the extruder to the front of the machine.
+Remove four screws from the cover of the head junction box.
 [[File:2.jpg]]
-Remove four screws from the cover of the head junction box.
+Loosen six terminal screws where the head cable wires attach. *may need to loosen the upper six terminal screws as wire may be held by upper screws as well
 [[File:3.jpg]]
 [[File:Strain_Relief_Cable_Glad.jpg]]

← Older revision		Revision as of 20:31, 9 January 2015
Line 1:		Line 1:
		+	Head cable replacement instructions:
		+
		+	For safety we're going to turn off the Gigabot and unplug the machine from the wall.
		+
		+	[[File:1.jpg]]
		+
		+	Move the extruder to the front of the machine.
		+
		+	[[File:2.jpg]]
		+
		+	Remove four screws from the cover of the head junction box.
		+
		+	[[File:3.jpg]]
		+
		+	Loosen six terminal screws where the head cable wires attach. *may need to loosen the upper six terminal screws as wire may be held by upper screws as well
		+
	[[File:Strain_Relief_Cable_Glad.jpg]]		[[File:Strain_Relief_Cable_Glad.jpg]]
		+
		+	Remove covers from vertical and horizontal Panduit.
		+
		+	Unwrap spiral wrap.
		+
		+	[[File:5.jpg]]
		+
		+	Remove cable grommet and head cable from in the head junction box.
		+	* The flex cable gland is shown; some Gigabots may have a regular cable grommet in it’s place.
		+
		+	[[File:6.jpg]]
		+
		+	Open electrical box door and loosen head cable wires from the Azteeg