Known problems - Revision history

Matthew at 15:29, 24 November 2015

2015-11-24T15:29:11Z

2015-11-24T15:28:55Z

2015-11-24T15:28:24Z

‎Shifting in the Y axis

2015-11-24T15:27:33Z

2015-10-31T02:02:41Z

‎Shifting in the Y axis

2015-10-31T01:51:15Z

‎Erratic movement in X, Y or Z axis

2015-10-31T01:50:46Z

‎Erratic movement in X, Y or Z axis

2015-10-31T01:50:19Z

‎Shifting in the Y axis

2015-10-31T01:49:37Z

‎Shifting in the Y axis

2015-10-31T01:37:10Z

‎Shifting in the Y axis

@@ Line 1: / Line 1: @@
-=== Extra movement in X, Y or Z axis ==
+=== Extra movement in X, Y or Z axis ===
 '''Do not rest the Viki LCD controller on top of the electrical enclosure'''
@@ Line 6: / Line 6: @@
 This can be caused by interference between the power supply in the electronics enclosure and the Viki LCD controller.
-=== Motor driver cooling and shifting in the Y axis==
+=== Motor driver cooling and shifting in the Y axis===
 '''Update''' Added cooling duct to reduce motor driver temperature
@@ Line 32: / Line 32: @@
 [[File:Enclosure.jpg]]
-=== V-Groove wheels may be out of round ==
+=== V-Groove wheels may be out of round ===
 We have found that some of our V-Groove wheels can be slightly out of round and cause the hot-end to move up and down as you move the print head in the X or Y axis. This should be immediately apparent if the dial indicator reading moves up and down in a cyclic fashion when you are leveling the bed. Please contact us at support@re3d.org if you need replacement wheels.
-=== Adding a second fan to the print head ==
+=== Adding a second fan to the print head ===
 We have also found the quality of PLA prints to improve when adding a second cooling fan to the print head.
 [[File:Second_head_fan.jpg|center|700px]]

@@ Line 1: / Line 1: @@
-== Extra movement in X, Y or Z axis ==
+=== Extra movement in X, Y or Z axis ==
 '''Do not rest the Viki LCD controller on top of the electrical enclosure'''
@@ Line 6: / Line 6: @@
 This can be caused by interference between the power supply in the electronics enclosure and the Viki LCD controller.
-== Motor driver cooling and shifting in the Y axis==
+=== Motor driver cooling and shifting in the Y axis==
 '''Update''' Added cooling duct to reduce motor driver temperature
@@ Line 32: / Line 32: @@
 [[File:Enclosure.jpg]]
-== V-Groove wheels may be out of round ==
+=== V-Groove wheels may be out of round ==
 We have found that some of our V-Groove wheels can be slightly out of round and cause the hot-end to move up and down as you move the print head in the X or Y axis. This should be immediately apparent if the dial indicator reading moves up and down in a cyclic fashion when you are leveling the bed. Please contact us at support@re3d.org if you need replacement wheels.
-== Adding a second fan to the print head ==
+=== Adding a second fan to the print head ==
 We have also found the quality of PLA prints to improve when adding a second cooling fan to the print head.
 [[File:Second_head_fan.jpg|center|700px]]

@@ Line 6: / Line 6: @@
 This can be caused by interference between the power supply in the electronics enclosure and the Viki LCD controller.
-== Shifting in the Y axis==
+== Motor driver cooling and shifting in the Y axis==
 '''Update''' Added cooling duct to reduce motor driver temperature

← Older revision		Revision as of 15:27, 24 November 2015
Line 1:		Line 1:
−	== ~~Erratic~~ movement in X, Y or Z axis ==	+	== Extra movement in X, Y or Z axis ==
	'''Do not rest the Viki LCD controller on top of the electrical enclosure'''		'''Do not rest the Viki LCD controller on top of the electrical enclosure'''

@@ Line 13: / Line 13: @@
 Measure the location of the side fan on your Gigabot electrical box.
-#Bottom of side fan to bottom of electrical box is greater than 3" [[File:Cooling_Duct_Rev01.STL]]
+#Bottom of side fan to bottom of electrical box is greater than 3" [[File:Cooling_Duct_new_model_GB_Rev01.STL]]
-#Bottom of side fan to bottom of electrical box is less than 3" [[File:Azteeg_HSF_Cooling_Old_GB2_Rev01.STL]]
+#Bottom of side fan to bottom of electrical box is less than 3" [[File:Cooling_Duct_older_model_GB_Rev01.STL]]

@@ Line 15: / Line 15: @@
 Measure the location of the side fan on your Gigabot electrical box.
-#Bottom of side fan to bottom of electrical box is greater than 3" [File:Cooling_Duct_Rev01.STL]
+#Bottom of side fan to bottom of electrical box is greater than 3" [[File:Cooling_Duct_Rev01.STL]]
-#Bottom of side fan to bottom of electrical box is less than 3" [File:Azteeg_HSF_Cooling_Old_GB2_Rev01.STL]
+#Bottom of side fan to bottom of electrical box is less than 3" [[File:Azteeg_HSF_Cooling_Old_GB2_Rev01.STL]]
 There are two reasons for shifting in the X or Y axis.